Insert into a sewer pipe - how to make a insert into a sewer pipe

There are times when, during the repair process, it is necessary to crash into the sewer riser. This may be due to the addition of any plumbing fixtures or, in general, a change in the layout of the apartment. Many do not know how and where to start, but do not be afraid. If you read the recommendations in this article, and perform all the actions correctly, the tie-in into the sewer pipe will be painless for both you and the neighbors. Let's take a closer look at the list of work that will have to perform.

Preparatory stage

So, you have firmly decided to insert the sewer into the sewer pipe and proceed to the preparatory one. Measure the diameter of the pipe into which you bump.

Look at the location of the pipe. If the pipe has free access, then it is possible to crash into the sewage system with the help of a tee. When the location of the pipe does not allow a tee to crash, you will have to perform this action with a special lining.

Before you begin, go around all the neighbors living above you and notify them of your repair. Otherwise, drained sewage into the sewer from the upper floors will get you into the apartment. Well, if you live on the top floor, you should not be afraid of this trouble.

So, you are ready to start work: the neighbors are notified, the tool is selected, all the necessary materials have been purchased.

Insertion in a plastic pipe

If you have a plastic sewage system installed in your apartment, then the process of inset is easy:

1. On the pipe mark the area under the tie-in tee, and using a grinder or a hacksaw for metal, cut it.
2. At cut points, remove all barbs for convenient connection.
3. Both edges of the pipe are abundantly lubricated with silicone for better sliding of the sealing rings.
4. At one end of the pipe, put on the slip clutch and slide it along the pipe.
5. On the second edge of the pipe, put on the socket tee. Do not forget to insert the sealing ring into the socket.
6. On the installed tee, moving along the pipe, put on the slip clutch.
7. If you are not going to immediately connect to the tee, insert a plug.

This is where the tie-in to the plastic pipe is considered completed.

Insertion into the cast-iron pipe

We cut into the cast-iron pipe

Having in the apartment cast iron sewers, you can also perform a sidebar. Only working with cast iron will be a little more difficult:

1. On the pipe you also mark the place of the tie-in of the tee and the Bulgarian cut out this piece.
2. You should file all the edges of the pipe with a file in order to remove the burrs.
3. Lubricate the edges of the pipe with silicone, and put on adapters from cast iron to plastic. First, wear rubber adapters. Lubricate them with sealant, and on top wear plastic adapters.
4. One edge of the adapter is smeared with silicone and put on the slip clutch.
5. Move the clutch through the adapter until it stops.
6. Lubricate the second edge of the plastic adapter with silicone, and put on the tee.
7. You lubricate the second edge of the coupling with silicone and, moving it through the pipe, connect it to the tee.
8. You install the plug on the tee, and on this the tie-in is ready.

Connection of plastic and cast iron pipe

If you put a plastic tee into the socket of a cast iron pipe then perform the following procedure:

1. Cut one edge of the cast-iron pipe with a grinder.
2. Clear the connection in the cast-iron socket and remove the cut piece of pipe.
3. Clean the cut edge with a file and lubricate with silicone, and clean the socket from dirt.
4. On the cut edge, put on the adapter from cast iron to plastic.
5. On the adapter, wear a slip clutch lubricated with silicone.
6. Insert the rubber adapter lubricated with silicone into the cast-iron socket.
7. Insert one edge of the tee into the socket with a rubber adapter, and on the second edge of the tee, slide the slip sleeve.
8. Twist the tee plug.

At this, the insert into the cast-iron pipe is ready, you can use the sewage system.

Other cases

With a plastic pipe

There are situations when sewers impossible to bump with a tee. For this there are special linings on the pipe. The essence of this lining is that for tie-in sewers do not need to cut a pipe segment. Let's take a look at this sidebar in more detail:

1. Buy a pad of the same diameter as the pipe to which you will connect.
2. Cut a window in the pipe, and clean the edges of the cut-off from agnails.
3. Grease the edges of the window with a sealant and put on the cover so that the drainage system coincides with the window on the pipe.
4. Attach the cover with clamps, and twist the cap on the drainage.

Connection on hose clamps

This method of tie-in is considered an emergency one. After all, the window size is impossible to fit perfectly to the size of the drainage system.Consequently, dirt will cling to the protrusions, and deposits will accumulate. But if there is nowhere to go, this method is also good.

This completes the details of the tie-in, you can safely get to work.

Video

In this video, the wizard shows how but performs the insertion of the cross in the sewer riser:

This video shows how to insert into the sewer pipe F110 firms HAAS (Germany):