How to pull a nail - removing nails

Sooner or later in construction there is a need to pull a nail out of an object. The reasons for this may be enough, you should know how to do it correctly. It is about how to pull a nail, we'll talk today.

Nail removal technology

A variety of tools can be used to remove nails today, for example:

• nail puller,
• tongs,
• pliers,
• a hammer with a forked spout, etc.

But despite the fact that there are a large number of tools, in order to pull out a nail, you will need ingenuity and ability to own or other tool. For successful work required to expose the nail head. In some cases, when the nail is exposed, it can be straightened and knocked out from the back side. This can be done with a hammer and other nail.

With the use of another nail

To make the nail easier to move, the protruding part can be lightly oiled with soap and water or fat. This grease allows you to quickly remove the nail. Especially it will be effective when the nail is rusted. In some cases, when pulling out a nail, a part of it may break. Then, using another nail, it is necessary to beat on its end face, which is located in the material. This action will raise the cap. For this purpose, you can use a suitable diameter rod or chisel.

It is not always possible to get close to the point of the nail. In most cases, it is located in the thickness of the workpiece. For this reason, it is necessary to pull the nail only by the cap. For this fit a chisel or a screwdriver, which has a rod that passes through the entire handle. Such a screwdriver will not break when hit on it with a hammer. As a result, a kind of mini-nail puller from a screwdriver will help to remove the nail from the cap. This screwdriver should have a forked blade that, when bent against the rod, will allow you to quickly complete the job.

Homemade nail puller with a screwdriver

But the nail head is not always available. In some cases, it is recessed into the workpiece. In such cases, to pull the nail, use a different technique. Make a small groove around the head with a chisel. The recess should be sufficient to allow the nail to be hooked onto the nail. If you didn’t succeed in catching the cap, then it’s best to cut it down, and remove the old nail to the opposite side. This requires knocking out a nail, as described above.

Pliers are a handy tool!

Pliers

One of the most convenient tools for extracting nails - tongs. It is best to have ticks of medium and small sizes. In order to make less effort to remove nails, it is recommended to purchase tongs with a long handle and sweeping jaws.

If your pincers have small handles, then it is not recommended to lengthen them using a tube. This can lead to injury!

If you decide to stretch a long nail, you cannot do without interception. Interception by pincers will be required when the rod comes out on 1 centimeter. Ticks should intercept the nail at the base of the workpiece. In this case, it will take effort, because the rod is smooth. In order to simplify this process, a plate is placed under the pincer support surface. This method will allow to remove nails from boards.

The nail can bend

Using this method, be careful, especially when you plan to reuse the nail . If you pull a nail with an interception and pull it exclusively in one direction, there is a risk of pulling the nail in the shape of a rainbow. To straighten it, you will need to peel it, as a rule, this process is quite laborious and laborious. Moreover, the perfect alignment will be extremely difficult. To prevent strong bending, pulling the nail, shake it in different directions.

Extraction with pliers

In order not to damage the surface of the workpiece when removing a nail with pliers or other assistants tool, it is reasonable to use a special lining. If the surface is lacquered, you can put the skin or other soft material under the plank.

A carpenter's hammer and pliers as an alternative to a nail puller!

As for a carpenter's hammer, this item can serve as an excellent service for extracting nails. Here you only need the hammer, which on the other hand has a forked spout. When using it without pads do not pull out a long nail. Therefore, the extraction takes place according to the method described above.

This method is effective, however, it carries danger. If the handle of the hammer is wooden, then its repeated use as a nail-catcher can break it. For this reason, it is best to have a hammer with a steel or polyurethane handle on the farm.

Using a hammer

Using tongs to pull out nails is much easier than using hammer Moreover, if the nail does not have a cap, then such a hammer will become completely useless, since it will simply slide along the rod.

As for the pliers, they are best used when there is no other suitable tool. The fact is that they are used only for stripping wires from insulation, etc. If they are constantly used to remove nails, the cutting elements will become dull or vyderbiritsya very quickly. In addition, you can bite the nail, especially if they are made of mild steel.

How to remove a nail from the board correctly?

In some situations, you will need to use several tools at once. In the event that a nail is hammered through the board and sticking out on the other side of the board for its entire length, you will first need to remove the nail with a hammer in the opposite direction. For starters, it is best to lubricate the nail with oil or grease to simplify the process. To prevent the nail core from becoming blunt, you can put an aluminum or brass plate. When the nail is completely knocked out, then the rest is required to be removed with tongs.

Removing long nails

Although not in all cases, you need to pull the nail out of the board. If it is no longer used, then the part with the nail sticking out can be simply cut with a hacksaw.

In another case, when the boards are already rotten and the nails are still in good condition, do not rush to throw them out. Nails can be removed by any of the above methods.

A convenient way to extract nails

If you have a large wooden structure that is knocked down by a large number of nails, here it is necessary to apply force. To begin, apply a few blows to this structure with a sledgehammer or hammer. This is necessary in order to form cracks between the knocked down parts. After they can insert an ax or a nail catcher. This barbaric method can be used to restructure a large wooden billet and, accordingly, remove the nails.

Here, perhaps, the most common methods that will help you, if necessary, to remove a nail from the wall, wooden blanks and not only. Now, if you do not have a nail catcher that is designed directly for this work, the above tips will help you cope with the task. Remember, not in all cases force plays a key role. Most often valued accuracy, because with the rush and great effort, you can bend a nail or tear a hat. Do not forget about safety measures: take care of your eyes and other parts of the body, because when pulling out nails there is a risk of injury.

Video

See the rusted nail extraction guide: